Ace trucks

[FatGuy92]

Expand Quote

Hey all. I'm planning on going down in board size (8.25 to 8.0) and am currently running 44s. I'm planning on getting 33s in the future but my 44s still have a lot of life left in them. Would they fit ok on a 8? I'm ok with the axels peeking out a tiny bit.

[close]

Ha I just did the opposite and put 33's on a 8.25 today. I have wanted to try Aces for a while now so I hope it works out.

Thanks! i'm pretty broad and stocky for my size (5'5") and need a skinny-ish board with wide wheelbase to feel stable. Was riding the new Austyn Habitat deck and that was almost perfect at 8.25x32x14.5 with Ace 44s. Gonna try out a 8.0 Toy Machine to see if that strikes a good balance.

[bigdave]

Expand Quote

Hey I am looking for some 55s in colors. Any of them will do, but prefer Bronze or Blue. If anyone knows of an online shop that has some, HMU.

[close]

http://www.35thave.com/shop/Skate/Trucks/Ace/p/Ace-55-9-axleTrucks-Classic-Shelby-Blue-set-of-2-x49700630.htm

You came up big! I picked up a set of blues and a tee from them. Thank you!

They had black as well for anyone interested.

[weon]

Polished and Matte Black are back in stock:

https://shop.acetrucks.com/collections/trucks

[jay_nev]

Just threw 55’s on today
Thanks @FrozenIndustries
200lbs so they feel loose for sure, trying not to tinker and just break in stock bushings. Top fell out past washer a bit but loosened em a quarter to half turn and kept riding to break em in and was fine after. Got 55mm OG classics on and may throw risers on while they break in more

[Murge]

Indy to venture back to Indy ( to hard to find short wb decks for venture) I want to try out some 44s. Am I just wasting money or is there a noticeable difference between Indy and ace

[moonordie]

Indy to venture back to Indy ( to hard to find short wb decks for venture) I want to try out some 44s. Am I just wasting money or is there a noticeable difference between Indy and ace

There is a noticeable difference, idk if you'll like it. I didn't, I tried 3 times ace and they just don't work for me. This year I skated like 3 different brands and I returned to Indy.

[FrozenIndustries]

Just threw 55’s on today
Thanks @FrozenIndustries
200lbs so they feel loose for sure, trying not to tinker and just break in stock bushings. Top fell out past washer a bit but loosened em a quarter to half turn and kept riding to break em in and was fine after. Got 55mm OG classics on and may throw risers on while they break in more

Let them break in but once you've ridden them for a bit there is nothing wrong with tightening them like 1/4 turn. I like them at stock with 44s but with the 55s I end up having them a little tighter to account for the width to height ratio or whatever. I'm glad they made it.

[spacial_profiling]

Can anyone confirm whether or not ACE are made under Paris trucks? Thought I heard this a while ago and now can't seem to find anyone who can confirm. Thanks!

[Lou Strux]

Can anyone confirm whether or not ACE are made under Paris trucks? Thought I heard this a while ago and now can't seem to find anyone who can confirm. Thanks!

I can 100% NOT confirm that for you at this time.
I CAN confirm that I have never heard THAT, however.

[22102020]

Okay, I've read a lot of this thread in the past, I've changed over to riding Ace trucks now. So, I just set-up a brand new deck today with Ace 44s and I can't ride them without either the top or bottom bushing escaping from the washer and messing it up. Is this normal? I did read that you just need to keep riding it and it will eventually settle?

Couldn't enjoy them yet since I can't ride for more than a minute without the bushings doing this, although the turning seems so great compared to my old indy 139s.

[BALARGUE]

Indy to venture back to Indy ( to hard to find short wb decks for venture) I want to try out some 44s. Am I just wasting money or is there a noticeable difference between Indy and ace

recently went from indy 144 to ACE 44 (on a 8.25")
I would say there is no huge difference
Got used to the new trucks pretty quickly

Imo, Aces are a bit more stable overall (grinds / manuals). A friend told me that crooked grinds are a bit different. I experienced it but i can't say if the huge crooked groove i had on my Indys isn't responsible for that feeling.

Overall i feel better on Aces

[Seventyfrigginseven]

I keep reading about how stable Aces are compared to Indy. I just got a pair of lightly used 33s, I love the quick turn but they seem to be very tippy when setting up for fliptricks. I only tightened the nuts a 1/4 turn from stock, because thats what I read people do on here(if they even adjust them at all) When the bushing break in do they become more stable?

[Gray Imp Sausage Metal]

Okay, I've read a lot of this thread in the past, I've changed over to riding Ace trucks now. So, I just set-up a brand new deck today with Ace 44s and I can't ride them without either the top or bottom bushing escaping from the washer and messing it up. Is this normal? I did read that you just need to keep riding it and it will eventually settle?

Couldn't enjoy them yet since I can't ride for more than a minute without the bushings doing this, although the turning seems so great compared to my old indy 139s.

just chill, they’ll harden up! Happened on my first session too. Don’t tinker with them, just take your time and break them in properly.

[Seventyfrigginseven]

Expand Quote

Okay, I've read a lot of this thread in the past, I've changed over to riding Ace trucks now. So, I just set-up a brand new deck today with Ace 44s and I can't ride them without either the top or bottom bushing escaping from the washer and messing it up. Is this normal? I did read that you just need to keep riding it and it will eventually settle?

Couldn't enjoy them yet since I can't ride for more than a minute without the bushings doing this, although the turning seems so great compared to my old indy 139s.

[close]

just chill, they’ll harden up! Happened on my first session too. Don’t tinker with them, just take your time and break them in properly.

Will do, thanks man!

[22102020]

Expand Quote

Okay, I've read a lot of this thread in the past, I've changed over to riding Ace trucks now. So, I just set-up a brand new deck today with Ace 44s and I can't ride them without either the top or bottom bushing escaping from the washer and messing it up. Is this normal? I did read that you just need to keep riding it and it will eventually settle?

Couldn't enjoy them yet since I can't ride for more than a minute without the bushings doing this, although the turning seems so great compared to my old indy 139s.

[close]

just chill, they’ll harden up! Happened on my first session too. Don’t tinker with them, just take your time and break them in properly.

Do I have to loosen them every time they pop out (to put them back under the washer) or just ride them till they get squashed out and broken in? It was literally any tight turn or jolt would send the bushings seeping out over the washer.

[jay_nev]

Okay, I've read a lot of this thread in the past, I've changed over to riding Ace trucks now. So, I just set-up a brand new deck today with Ace 44s and I can't ride them without either the top or bottom bushing escaping from the washer and messing it up. Is this normal? I did read that you just need to keep riding it and it will eventually settle?

Couldn't enjoy them yet since I can't ride for more than a minute without the bushings doing this, although the turning seems so great compared to my old indy 139s.

Same situation with a set of 55's i set up this week. I loosened the nut about a 1/4 turn or so and it seemed to resolve that issue. Looks like you have some kingpin thread left to loosen. Others with more experience may have a different answer but this seemed to work for me until the bushings break in a bit.

[FrozenIndustries]

Okay, I've read a lot of this thread in the past, I've changed over to riding Ace trucks now. So, I just set-up a brand new deck today with Ace 44s and I can't ride them without either the top or bottom bushing escaping from the washer and messing it up. Is this normal? I did read that you just need to keep riding it and it will eventually settle?

Couldn't enjoy them yet since I can't ride for more than a minute without the bushings doing this, although the turning seems so great compared to my old indy 139s.

Yes, generally it will. If it bothers you a lot, take the washers from you Indys and put them in there.

[Sloppy Krooks]

Okay, I've read a lot of this thread in the past, I've changed over to riding Ace trucks now. So, I just set-up a brand new deck today with Ace 44s and I can't ride them without either the top or bottom bushing escaping from the washer and messing it up. Is this normal? I did read that you just need to keep riding it and it will eventually settle?

Couldn't enjoy them yet since I can't ride for more than a minute without the bushings doing this, although the turning seems so great compared to my old indy 139s.

Apparently you haven’t read enough. This seems to be extremely common, and tends to happen less as the bushings harden

[TheAvidBleeder]

Happened to me with my last set of 44’s and 55’s.  I loosened them up a bit until it quit happening then gradually started tightening them down to my liking as the bushings broke in.   My old sets never did this, but both new sets are perfectly fine now and turn great.

[Diocletian]

It's the Ace washers, swap them for Indy's if you have them lying around. I use Ace stock with a Krux bottom washer and no top washer.

[bigdave]

RANDO QUESTION. Sorry if it's a dumb one.

Are baseplates compatible among aces? I dont imagine the turning radius changes, ergo the baseplates should be fine. but I want to run 55 baseplates on 66 hangers.

Will work, yes?

[Firebert]

yes

[bigdave]

Expand Quote

yes

[close]

Grassy-ass, kind sir!

[uptherecazaly]

I've heard that using the inside speed ring/spacer/washer is optional on Ace trucks because the hanger tapers down. Has anyone got experience with this? I know the difference might be negligible, but I'd like to have my wheels a tad closer together on my 66s. (Don't tell me to get 55s, I already do.)

EDIT: To clarify, I want to remove the inside rings so that the bearings will be directly on the hanger.

[Glutenpadre]

I've heard that using the inside speed ring/spacer/washer is optional on Ace trucks because the hanger tapers down. Has anyone got experience with this? I know the difference might be negligible, but I'd like to have my wheels a tad closer together on my 66s. (Don't tell me to get 55s, I already do.)

EDIT: To clarify, I want to remove the inside rings so that the bearings will be directly on the hanger.

I've been riding my Ace 44s without speed rings, barely noticeable and seems fine no complications so far.

[Thomas]

Expand Quote

I've heard that using the inside speed ring/spacer/washer is optional on Ace trucks because the hanger tapers down. Has anyone got experience with this? I know the difference might be negligible, but I'd like to have my wheels a tad closer together on my 66s. (Don't tell me to get 55s, I already do.)

EDIT: To clarify, I want to remove the inside rings so that the bearings will be directly on the hanger.

[close]

I've been riding my Ace 44s without speed rings, barely noticeable and seems fine no complications so far.

Why do you want to do that ?
I don't think this will cause any issue, but you will probably have more visible threads and will most likely destroy them sooner.

[Krooked antihero]

Expand Quote

Expand Quote

I've heard that using the inside speed ring/spacer/washer is optional on Ace trucks because the hanger tapers down. Has anyone got experience with this? I know the difference might be negligible, but I'd like to have my wheels a tad closer together on my 66s. (Don't tell me to get 55s, I already do.)

EDIT: To clarify, I want to remove the inside rings so that the bearings will be directly on the hanger.

[close]

I've been riding my Ace 44s without speed rings, barely noticeable and seems fine no complications so far.

[close]

Why do you want to do that ?
I don't think this will cause any issue, but you will probably have more visible threads and will most likelydestroy them sooner.

[FrozenIndustries]

I've heard that using the inside speed ring/spacer/washer is optional on Ace trucks because the hanger tapers down. Has anyone got experience with this? I know the difference might be negligible, but I'd like to have my wheels a tad closer together on my 66s. (Don't tell me to get 55s, I already do.)

EDIT: To clarify, I want to remove the inside rings so that the bearings will be directly on the hanger.

With my 55s, I've pretty much always run them with both washers outside. Its fine, thats part of Aces design and it doesn't fuck with the speed at all. I keep the washers on the outside to keep the axle threads from being exposed.

[Frank and Fred]

Same as above.

[Hash Slinging Slasher]

Indy to venture back to Indy ( to hard to find short wb decks for venture) I want to try out some 44s. Am I just wasting money or is there a noticeable difference between Indy and ace

had a similar thought recently related to thunders. deck width doesn't matter to me as much but realized i've really limited myself to trying to find short decks with 14" wheelbase or just a hair over, which have been hard to find. would ace or indy open up the field a bit? seems like 14.25 is sort of the norm right now