Gear madness support thread

[Sedition]

Am I thinking about this totally wrong here?

Maybe? I am not a physics guy, at all, so i could be totally off here....but I feel like the V3 might be able to slide off the coping much easier (roll up/off of it), because of the wheel shape. Think about plate tectonics where one plate slides under/over another, rather than rubbing against more at a direct angle...I feel like that's what the V3 is here, and it might "slip out" more??? I know my Classics don't "lock" as good on round coping as Conicals, Tablets, etc. If I had to Smith/Feeble/Crook a round rail, I think I'd want Classics/V3. If I was going to 50-50/5-0 it, I think I'd want something more squared off. Does this make any sense, or am I just crazy?

[OhioGuy]

What cured my madness is realizing that I was only confusing myself by always switching shit up, and that I was doing it cause I felt like other areas of my life were out of my control.

I’ve been stressed lately and the madness is trying to come back. So I’ve spent the last two hours on Tactics looking at gear.

Didn’t buy anything, though. I’m just over switching gear. Need to find another way to cope with life.

[Tom Pearl]

What cured my madness is realizing that I was only confusing myself by always switching shit up, and that I was doing it cause I felt like other areas of my life were out of my control.

I’ve been stressed lately and the madness is trying to come back. So I’ve spent the last two hours on Tactics looking at gear.

Didn’t buy anything, though. I’m just over switching gear. Need to find another way to cope with life.

gear sadness

[OhioGuy]

Expand Quote

What cured my madness is realizing that I was only confusing myself by always switching shit up, and that I was doing it cause I felt like other areas of my life were out of my control.

I’ve been stressed lately and the madness is trying to come back. So I’ve spent the last two hours on Tactics looking at gear.

Didn’t buy anything, though. I’m just over switching gear. Need to find another way to cope with life.

[close]

gear sadness

😭😭😭

Pretty much lol

[Ok]

Expand Quote

Expand Quote

What cured my madness is realizing that I was only confusing myself by always switching shit up, and that I was doing it cause I felt like other areas of my life were out of my control.

I’ve been stressed lately and the madness is trying to come back. So I’ve spent the last two hours on Tactics looking at gear.

Didn’t buy anything, though. I’m just over switching gear. Need to find another way to cope with life.

[close]

gear sadness

[close]

😭😭😭

Pretty much lol

firm agreement

[Mbrimson88]

Expand Quote

What cured my madness is realizing that I was only confusing myself by always switching shit up, and that I was doing it cause I felt like other areas of my life were out of my control.

I’ve been stressed lately and the madness is trying to come back. So I’ve spent the last two hours on Tactics looking at gear.

Didn’t buy anything, though. I’m just over switching gear. Need to find another way to cope with life.

[close]

gear sadness

That is the definition of having everything you want but not being able to skate any more, or not being able to skate enough to use it.

I feel like that sometimes, especially when I think about something or somewhere I used to skate that I would really enjoy and not be too afraid, like I am now, such as big bowls or something similar.

Not to worry though.  I just remember it is better to still be able to roll around more than it is to be able to do certain tricks or hit certain things, so as long as I can do that, I am still going to be happy enough to deal with everything else going on.

[OhioGuy]

Expand Quote

Expand Quote

What cured my madness is realizing that I was only confusing myself by always switching shit up, and that I was doing it cause I felt like other areas of my life were out of my control.

I’ve been stressed lately and the madness is trying to come back. So I’ve spent the last two hours on Tactics looking at gear.

Didn’t buy anything, though. I’m just over switching gear. Need to find another way to cope with life.

[close]

gear sadness

[close]

That is the definition of having everything you want but not being able to skate any more, or not being able to skate enough to use it.

I feel like that sometimes, especially when I think about something or somewhere I used to skate that I would really enjoy and not be too afraid, like I am now, such as big bowls or something similar.

Not to worry though.  I just remember it is better to still be able to roll around more than it is to be able to do certain tricks or hit certain things, so as long as I can do that, I am still going to be happy enough to deal with everything else going on.

Totally. I started at 35 and my body holds me back the most. So I leaned heavily into gear at first, as if I could buy my way into being a “real” skater.

I’m 245 lbs and 6’4 and years of physical labor and playing basketball in school has destroyed my knees. Plus the weight don’t help.

Luckily I love rolling around on tennis courts. I can do that for hours without doing a single trick. It feels good just to get better at actually riding 😃

One thing I enjoy about skateboarding is it can be whatever you want it to be.

[Deadringer]

Expand Quote

Expand Quote

Expand Quote

What cured my madness is realizing that I was only confusing myself by always switching shit up, and that I was doing it cause I felt like other areas of my life were out of my control.

I’ve been stressed lately and the madness is trying to come back. So I’ve spent the last two hours on Tactics looking at gear.

Didn’t buy anything, though. I’m just over switching gear. Need to find another way to cope with life.

[close]

gear sadness

[close]

That is the definition of having everything you want but not being able to skate any more, or not being able to skate enough to use it.

I feel like that sometimes, especially when I think about something or somewhere I used to skate that I would really enjoy and not be too afraid, like I am now, such as big bowls or something similar.

Not to worry though.  I just remember it is better to still be able to roll around more than it is to be able to do certain tricks or hit certain things, so as long as I can do that, I am still going to be happy enough to deal with everything else going on.

[close]

Totally. I started at 35 and my body holds me back the most. So I leaned heavily into gear at first, as if I could buy my way into being a “real” skater.

I’m 245 lbs and 6’4 and years of physical labor and playing basketball in school has destroyed my knees. Plus the weight don’t help.

Luckily I love rolling around on tennis courts. I can do that for hours without doing a single trick. It feels good just to get better at actually riding 😃

One thing I enjoy about skateboarding is it can be whatever you want it to be.

Heard someone the other day ask this kid how good they were at skating. It made me think that it doesn’t really matter, the real question you need to ask yourself is how much fun/enjoyment it brings you.

If rolling around brings you that joy, then you’re great at skateboarding. Have loads of gear? Sweet, that’s what brings you joy. ☺️

[Scottboarding]

Expand Quote

Expand Quote

Expand Quote

Expand Quote

What cured my madness is realizing that I was only confusing myself by always switching shit up, and that I was doing it cause I felt like other areas of my life were out of my control.

I’ve been stressed lately and the madness is trying to come back. So I’ve spent the last two hours on Tactics looking at gear.

Didn’t buy anything, though. I’m just over switching gear. Need to find another way to cope with life.

[close]

gear sadness

[close]

That is the definition of having everything you want but not being able to skate any more, or not being able to skate enough to use it.

I feel like that sometimes, especially when I think about something or somewhere I used to skate that I would really enjoy and not be too afraid, like I am now, such as big bowls or something similar.

Not to worry though.  I just remember it is better to still be able to roll around more than it is to be able to do certain tricks or hit certain things, so as long as I can do that, I am still going to be happy enough to deal with everything else going on.

[close]

Totally. I started at 35 and my body holds me back the most. So I leaned heavily into gear at first, as if I could buy my way into being a “real” skater.

I’m 245 lbs and 6’4 and years of physical labor and playing basketball in school has destroyed my knees. Plus the weight don’t help.

Luckily I love rolling around on tennis courts. I can do that for hours without doing a single trick. It feels good just to get better at actually riding 😃

One thing I enjoy about skateboarding is it can be whatever you want it to be.

[close]

Heard someone the other day ask this kid how good they were at skating. It made me think that it doesn’t really matter, the real question you need to ask yourself is how much fun/enjoyment it brings you.

If rolling around brings you that joy, then you’re great at skateboarding. Have loads of gear? Sweet, that’s what brings you joy. ☺️

I’m mildly self conscious about my lack of skill and reading this made me really happy. I don’t think I’ve learned a new trick in close to a year but I’ve had fun every time I stepped on the board in that same timeframe.

[j....soy.....]

I even think doing the same tricks on different stuff is actually a pretty solid way of enjoying skating.  Trying new things and tinkering is fun too.

The part that I don't see constructive is inducing an unhealthy level of of stress upon oneself.



 

[OhioGuy]

I even think doing the same tricks on different stuff is actually a pretty solid way of enjoying skating.  Trying new things and tinkering is fun too.

The part that I don't see constructive is inducing an unhealthy level of of stress upon oneself.

Tinkering is fun. It becomes dangerous when you say, “If I change this, I’ll be better at that.” Outside of major changes like going from an 8 to 8.5, or changing truck brands, a lot of it doesn’t matter.

[Vintagebody]

I'm starting to feed the madness again. Came home from a session, and I notice my axle is bent. Dont even have that deep of a k-grind groove. So I swapped to some indys I have laying around. I just hate how they are kinda unstable at center, and turn so easly. My luck with Thunder has been terrible. Broken kingpins, and now bent axle. Kinda dont want to buy them again. I guess venture is the most similar?

[hiljentaa]

I'm starting to feed the madness again. Came home from a session, and I notice my axle is bent. Dont even have that deep of a k-grind groove. So I swapped to some indys I have laying around. I just hate how they are kinda unstable at center, and turn so easly. My luck with Thunder has been terrible. Broken kingpins, and now bent axle. Kinda dont want to buy them again. I guess venture is the most similar?

Highly recommend Ventures. The stability is so helpful while setting up. They turn just fine, too.

[Mbrimson88]

Expand Quote

I'm starting to feed the madness again. Came home from a session, and I notice my axle is bent. Dont even have that deep of a k-grind groove. So I swapped to some indys I have laying around. I just hate how they are kinda unstable at center, and turn so easly. My luck with Thunder has been terrible. Broken kingpins, and now bent axle. Kinda dont want to buy them again. I guess venture is the most similar?

[close]

Highly recommend Ventures. The stability is so helpful while setting up. They turn just fine, too.

From working in and around skate shops for 20+ years, I would go as far as to say "Everything breaks" so if the Thunder brand truck works for you besides broken kingpins or bent axles, going to a different truck might not really solve anything.

That said, I know I have definitely had bad experiences in the past, not just skateboarding, that puts me off something or someone for good, so by all means give something else a go.


As said, Venture is more stable and a lot of people skate the trucks, so something new could be the answer here too and you might find they work well and then you stick with them, especially if right now you are looking at buying a new set of something.

In the mean time, using slightly harder bushings on Indy would definitely firm up the turn on your existing trucks, even if it is just a temporary fix until you source a new set of trucks.  You might be surprised how much more stable they can feel on harder bushings, but yes they will turn a lot more than Ventures and a bit more than Thunder, depending on how you have them set up.

[eviltgirl]

Are you guys really noticing 1/8" of a wheelbase change in your boards?  Thinking about going from a 14.38 to a 14.25 and before i order the deck im wondering if its actually a big deal and something I'll even notice. If so what are the actual changes I'll feel?

[goodatmeth]

Are you guys really noticing 1/8" of a wheelbase change in your boards?  Thinking about going from a 14.38 to a 14.25 and before i order the deck im wondering if its actually a big deal and something I'll even notice. If so what are the actual changes I'll feel?

People think they do, but it's most likely in combination with other changes. Who actually gets the exact same deck with only a 1/8 wb difference? Same steepness and every other spec...

[IpathCats]

Expand Quote

Are you guys really noticing 1/8" of a wheelbase change in your boards?  Thinking about going from a 14.38 to a 14.25 and before i order the deck im wondering if its actually a big deal and something I'll even notice. If so what are the actual changes I'll feel?

[close]

People think they do, but it's most likely in combination with other changes. Who actually gets the exact same deck with only a 1/8 wb difference? Same steepness and every other spec...

Yea, most of the time it isnt just the WB changing.

even if the boards are the same width/length, the kick steepness and fingers of flat play a big role in feel.

[LebowskisRug]

Expand Quote

Are you guys really noticing 1/8" of a wheelbase change in your boards?  Thinking about going from a 14.38 to a 14.25 and before i order the deck im wondering if its actually a big deal and something I'll even notice. If so what are the actual changes I'll feel?

[close]

People think they do, but it's most likely in combination with other changes. Who actually gets the exact same deck with only a 1/8 wb difference? Same steepness and every other spec...

Yah this- like if I went from 14.25 with mellow kicks to 14.38 with steep I'll notice but if everything is the same I'll get used to it fast. Now if I did the same and switched brands, like I did going from a Sci Fi to a Girl where there was way more flat before the kicks, it will feel insane.

[OhioGuy]

Expand Quote

Expand Quote

Are you guys really noticing 1/8" of a wheelbase change in your boards?  Thinking about going from a 14.38 to a 14.25 and before i order the deck im wondering if its actually a big deal and something I'll even notice. If so what are the actual changes I'll feel?

[close]

People think they do, but it's most likely in combination with other changes. Who actually gets the exact same deck with only a 1/8 wb difference? Same steepness and every other spec...

[close]

Yea, most of the time it isnt just the WB changing.

even if the boards are the same width/length, the kick steepness and fingers of flat play a big role in feel.

Yeah. Also it seems like I need to adjust my trucks when I change shapes. Cause the turning feels different. It’s weird.

[TheCrimsonShroud]

I have a set of bones reds that are nice and broken in. Cleaned and re-lubed them. Now they only keep speed in one set of softer wheels I have. I’ve tried them in almost every other set of wheels I have and three whole ass kicks will get me maybe 20 feet. Sometimes I fucking hate skateboards.

[Ok]

I have a set of bones reds that are nice and broken in. Cleaned and re-lubed them. Now they only keep speed in one set of softer wheels I have. I’ve tried them in almost every other set of wheels I have and three whole ass kicks will get me maybe 20 feet. Sometimes I fucking hate skateboards.

yeah i hate skateboards too, but not as much as i hate reds.
i’ve never had a good set of reds. i’m
currently swiss, and then on another setup mini logos. the swiss are better in every way, but the mini logos are better than the other brands of bearing i’ve had recently.
i’d like to get some swiss 6, and try ceramics, but i’ll probably not, my skating doesn’t deserve or need any of that.
i do not like reds.

[manysnakes]

Swiss cost twice as much as Reds and last for years and years. Unless you really can't afford the $50-60 for Swiss (I always wait for a sale), it's "pennywise, pound foolish" to be buying cheapo bearings after cheapo bearings.

[Boog]

Swiss cost twice as much as Reds and last for years and years. Unless you really can't afford the $50-60 for Swiss (I always wait for a sale), it's "pennywise, pound foolish" to be buying cheapo bearings after cheapo bearings.

[OhioGuy]

I want some Swiss. But my Bronson G3s still work great after 7 months. Maybe one day. I feel like my gear last forever since I only skate a few hours a week 😭

[TheCrimsonShroud]

Expand Quote

I have a set of bones reds that are nice and broken in. Cleaned and re-lubed them. Now they only keep speed in one set of softer wheels I have. I’ve tried them in almost every other set of wheels I have and three whole ass kicks will get me maybe 20 feet. Sometimes I fucking hate skateboards.

[close]

yeah i hate skateboards too, but not as much as i hate reds.
i’ve never had a good set of reds. i’m
currently swiss, and then on another setup mini logos. the swiss are better in every way, but the mini logos are better than the other brands of bearing i’ve had recently.
i’d like to get some swiss 6, and try ceramics, but i’ll probably not, my skating doesn’t deserve or need any of that.
i do not like reds.

I got some mini logo bearings that broke in pretty much instantly. Also have a set of globes that were rusted out. Soaked ‘em in windex, re-lubed, and now they fly. I dunno, I tend to have bad luck with “nice” things (reds), and good luck with shitty things.

[LebowskisRug]

Swiss cost twice as much as Reds and last for years and years. Unless you really can't afford the $50-60 for Swiss (I always wait for a sale), it's "pennywise, pound foolish" to be buying cheapo bearings after cheapo bearings.

buy nice or buy twice

[Sedition]

Swiss 6 or nothing.

[Texas_Tone]

I’ve been on ace lows for a bit now really liking them, but the more and more I peruse the new royal thread I can feel the madness setting in, I’m concerned with the bushing and other aspects of the royals but it’s still enticing me to try them out, I had to switch to the ace hard low bushings for my current setup so switching out bushings isn’t really a deal breaker for me, should I switch up? Or stay the course til ace decides to discontinue the lows? Which I can see happening sooner or later

[LebowskisRug]

I don't see what you would gain unless you want a higher truck for some reason. Worry about discontinuation when it actually happens if it happens. I feel if you find your happy place with truck choice just stay there.

[backside_frontside]

I’ve been on ace lows for a bit now really liking them, but the more and more I peruse the new royal thread I can feel the madness setting in, I’m concerned with the bushing and other aspects of the royals but it’s still enticing me to try them out, I had to switch to the ace hard low bushings for my current setup so switching out bushings isn’t really a deal breaker for me, should I switch up? Or stay the course til ace decides to discontinue the lows? Which I can see happening sooner or later

You need to try every truck brand and bushing combo before you can know for sure. Leave no stone unturned